Skip to content
AtomicHobbies

Small hobbies for the gaps in your day.

All hobbies
Craftsbeginner30 minutes

Darning

fixes a hole by weaving a small new piece of cloth right into it: a row of threads one way, then a row over and under them the other way. It is the old way to save socks and sweaters, and a contrasting color turns the repair into a neat little checkerboard. A needle, some floss or yarn, and a mug to stretch the sock over are all it takes.

What you'll do

Stretch a sock with a small hole over a mug or an orange, lay about 11 parallel threads across the hole, then weave about 11 rows over and under them so a small woven patch fills it.

A sock with a small woven checkerboard darn in brass and cream on its foot, and a threaded needle beside it

At a glance

Time
30 minutes for your first session
Cost
Nothing to buy. It uses things you already have at home.
You need
A sock with a small hole or a worn-thin spot, Something round and firm to stretch it over, Needle with an eye the thread fits through, Thin yarn or embroidery floss, about 2 m (80 inches), A hair tie or rubber band, and scissors

What you need

Required

  • A sock with a small hole or a worn-thin spot × 1 sock, with a hole no bigger than 1 cm (3/8 inch), about a fingertip · $0 · household

    Clean and dry. A knitted wool or cotton sock with a heel or toe hole is the classic first darn; a thin spot that has not opened yet works the same way. Leave bigger holes and thin athletic socks with lots of stretch for later. No damaged sock? Practice on a thin spot of an old sock or a knitted glove.

    Alternatives: A knitted glove, hat or sweater with a small hole

  • Something round and firm to stretch it over × 1 · $0 · household

    This stands in for a darning egg. The bottom of a narrow mug or glass, the bowl of a ladle, an orange, a tennis ball or a smooth stone all work. Only the part under the hole has to go inside the sock, and it must not stretch the sock wider than your foot does. It keeps the hole flat and stops you stitching through to the other side.

    Alternatives: Ladle, Orange, Tennis ball

  • Needle with an eye the thread fits through × 1 · $0 · household

    A blunt tapestry or yarn needle is best because it slides between threads without splitting them. A sharp sewing needle works too: weave with the eye end first so the point does not snag.

  • Thin yarn or embroidery floss, about 2 m (80 inches) × 2 lengths of 1 m (40 inches) · $0 · household

    Leftover sock or fingering-weight yarn is ideal. Embroidery floss with all 6 strands works well. With only sewing thread, thread two 1 m pieces together and double them, so 4 strands lie in each pass. A contrasting color makes the checkerboard show and is easier to follow on a first try.

    Alternatives: Embroidery floss, all 6 strands, 4 strands of sewing thread, Thin crochet cotton

  • A hair tie or rubber band, and scissors × 1 of each · $0 · household

    The band holds the sock snug on the mug or orange so it does not slide while you weave.

Nice to have

  • Darning mushroom or darning egg × 1 · $7-15 · purchased

    A wooden mushroom has a handle to hold and a groove for the band. Nice to have once you mend often.

  • Pack of blunt tapestry needles × 1 pack · $2-5 · purchased

    Large eyes take yarn easily and the rounded tips never split the threads you weave through.

How to do it

  1. Snip any fuzzy, loose ends around the hole so nothing longer than 3 mm (1/8 inch) sticks out; do not cut into the knitting itself. Keep the sock right side out. Push the bottom of the mug (or the ladle bowl or orange) into the sock from the open end until the hole sits centered on top of it. With a mug, only the base needs to go in; if it stretches the sock wider than your foot does, use a narrower glass, a tennis ball or an orange instead. Wrap the hair tie around the sock and the mug below the hole, twice if it is loose, so the sock is snug. It should be stretched about as much as it is on your foot, not more. It worked if the hole lies open and flat on the mug and the little V-shaped knit stitches around it look even, like they do when worn. Common mistake: stretching the sock drum-tight. The woven patch does not stretch, so a patch made on an over-stretched sock bunches up when you take it off.

    Show help

    darning egg: A smooth, egg-shaped tool slid inside a sock to hold it in shape while you darn.

    Tip: Common mistake: pulling the thread tight. A darn should sit flat on the surface like a tiny woven mat. If the sock puckers around it, loosen the last few rows by easing them with the needle tip.

  2. Cut 1 m (40 inches) of yarn or floss and thread the needle. To thread thick yarn, fold 1 cm over the needle, pinch the fold flat, slide the needle out and push the fold through the eye. Pull 15 cm (6 inches) through and keep it single. Do not tie a knot: knots rub inside a shoe. Starting at what will be the top right corner, sew a square of small running stitches (needle down, up, down, up) through the sock only, about 5 mm (1/4 inch) outside the hole on every side. For a 1 cm hole the square is about 2 cm (3/4 inch) across. Leave a 10 cm (4 inch) tail hanging where you started, and finish back at that top right corner. It worked if a dashed square circles the hole with healthy knitting inside it all round. Common mistake: drawing the square right at the edge of the hole, where the knitting is already worn thin and will tear again. Go out to firm fabric.

    Show help

    running stitch: The simplest hand stitch: the needle goes down and up along a line, leaving a dashed line of thread on top.

    Tip: Common mistake: pulling the thread tight. A darn should sit flat on the surface like a tiny woven mat. If the sock puckers around it, loosen the last few rows by easing them with the needle tip.

  3. The is a set of parallel threads that runs from the top of the square to the bottom, like the strings of a guitar. Start at the top right corner of the square. Take a tiny stitch in the knitting there, about 2 mm (1/16 inch) long, sideways from right to left. Carry the thread straight down over the hole to the bottom edge of the square and take another 2 mm sideways stitch there, right to left. That stitch brings the needle out 2 mm to the left, where the next thread starts: carry it straight back up, take another 2 mm right-to-left stitch at the top, and keep going: down, up, down, up, each thread about 2 mm apart (about one column of knit stitches). Stop when the threads cover the hole and reach the left side of the square. Count them: an odd number, such as 9 or 11, makes the weaving come out even and leaves your needle at the bottom left corner, so add one more if you have an even number. It worked if the threads lie side by side, parallel, flat on the mug and evenly spaced, with no gap wider than a thread. Common mistake: pulling each thread tight, which draws the edges of the hole together and puckers the sock. Each thread should just touch the mug.

    Show help

    warp: The set of parallel threads you lay first, running in one direction across the hole.

    Tip: Common mistake: pulling the thread tight. A darn should sit flat on the surface like a tiny woven mat. If the sock puckers around it, loosen the last few rows by easing them with the needle tip.

  4. The runs across the , at right angles. At the bottom left corner of the square, take a tiny stitch in the knitting just outside the first warp thread so the weft starts anchored. Now weave across from left to right: over the first warp thread, under the second, over the third, and so on to the last one. Pick up the warp threads with the eye end of the needle (or a blunt tip) so you go between them, never through them. Pull the thread across until it lies flat, take a tiny stitch in the knitting on the right side, 2 mm above the row you just made, and weave back the other way with the opposite pattern: under the threads you went over last time, over the ones you went under. Every 3 rows, use the needle tip to nudge the rows down against each other. Keep going up the square until the woven part covers the hole and reaches the top. If your thread runs short, leave a 10 cm tail on the surface, start a new length the same way with a 10 cm tail, and carry on. It worked if the patch shows a small checkerboard with no gaps and no warp threads loose on top. Common mistake: repeating the same over-under pattern as the row before, which leaves the new row lying on top instead of locking in. Look at each finished row: every thread should cross in the opposite way to its neighbor.

    Show help

    weft: The threads you weave across the warp at right angles, going over one and under the next.

    Tip: Common mistake: pulling the thread tight. A darn should sit flat on the surface like a tiny woven mat. If the sock puckers around it, loosen the last few rows by easing them with the needle tip.

  5. Thread each tail in turn: the start tail, the end of the , and any you left when changing thread. Slide the needle under the edge of the woven patch, through 4 or 5 rows of weaving on the outside of the sock, then trim the tail to 5 mm (1/4 inch). Weaving tails on the outside keeps the inside smooth against your foot. Take off the hair tie and pull the sock off the mug. It worked if a gentle tug on the patch moves nothing and the inside of the sock shows only small stitches, no loops or long tails. Common mistake: tying the ends in a knot on the inside. It makes a hard lump you feel with every step; weaving holds just as well.

    Show help

    Tip: Common mistake: pulling the thread tight. A darn should sit flat on the surface like a tiny woven mat. If the sock puckers around it, loosen the last few rows by easing them with the needle tip.

  6. Put the sock on and walk a few steps. The patch should lie flat and feel smooth; a slightly thick darn flattens after a wash or two, and you can also steam it with an iron on the setting for the sock's fiber, holding the iron just above the darn rather than pressing. If a corner gapes, weave a short extra row there. You did it: the hole is filled with new woven cloth and the sock goes back in the drawer instead of the bin. Next session, darn a worn-thin heel before it opens, or try a bigger hole with a second color for the so the checkerboard really shows. Once you like mending, sashiko is the next step for patching holes in jeans and shirts.

    Show help

    Tip: Common mistake: pulling the thread tight. A darn should sit flat on the surface like a tiny woven mat. If the sock puckers around it, loosen the last few rows by easing them with the needle tip.

Darning · Step 1 of 6

Tips

  • Common mistake: pulling the thread tight. A darn should sit flat on the surface like a tiny woven mat. If the sock puckers around it, loosen the last few rows by easing them with the needle tip.

  • Always keep the mug, orange or ladle inside while you stitch. Without it, it is easy to catch the other side of the sock and sew it shut.

  • Use a contrasting color for your first darn. It is easier to see which threads you went over and under, and the checkerboard looks deliberate rather than like a failed hidden repair.

  • Darn thin spots before they open. Once you can see your skin through the knitting, a quick darn across the thin area saves the sock in half the time a hole takes.

  • Match thickness: thin thread in a chunky sock leaves gaps, and thick yarn in a fine sock makes a hard lump. Pick something close to the thickness of the sock's own yarn.

Glossary

darning
Repairing a hole or thin spot by weaving new thread across it, so the gap fills with a small piece of new cloth.
warp
The set of parallel threads you lay first, running in one direction across the hole.
weft
The threads you weave across the warp at right angles, going over one and under the next.
darning egg
A smooth, egg-shaped tool slid inside a sock to hold it in shape while you darn.
running stitch
The simplest hand stitch: the needle goes down and up along a line, leaving a dashed line of thread on top.
Swiss darning
A different repair that follows the sock's own V-shaped knit stitches with new yarn, used to strengthen thin spots before they become holes.

Communities

Resources

Frequently asked questions

How long does it take to learn darning?

A first darn on a fingertip-sized hole takes about 30 minutes. After 2 or 3 socks the warp and weave go quickly, and a small hole takes 10 to 15 minutes.

Do I need a darning egg or special yarn?

No. A mug, ladle, orange or tennis ball holds the sock just as well, and leftover thin yarn or all 6 strands of embroidery floss make a good darn. A wooden darning mushroom ($7-15) and blunt tapestry needles are nice upgrades if you start mending often.

How is darning different from sashiko or patching?

Darning weaves new threads into the hole itself, so nothing is added on top or behind. Sashiko and patching cover a hole with a separate piece of fabric held by rows of stitches. Darning suits knitted things like socks and sweaters; patching suits woven cloth like jeans and shirts.

Why does my darn pucker the sock?

The thread was pulled too tight, or the sock was stretched too far on the mug. Ease the rows looser with the needle tip and, next time, stretch the sock only as much as it stretches on your foot.

Will the darn be uncomfortable in a shoe?

Not if you skip knots and weave the tails in on the outside. A new darn feels a little thick but flattens after a wash or two. Thread close to the thickness of the sock's own yarn keeps it smooth.

Can I darn a big hole?

Yes, the method is the same with more warp threads and more rows, but start with a hole no bigger than a fingertip. For holes wider than about 3 cm (1 1/4 inches), many menders use a small darning loom or knit a patch instead.

Something off in this guide?

Tried it? Earn the badge

Rate it below and the Darning badge goes in your account.

How was it?

How much of a challenge was it?

Pass it on

Did you enjoy darning? Share it with your friends!

Someone you know has 30 spare minutes too.

Sign in

A free account: just your email, no password. We'll email you a link that brings you back here.

No password. We only use your email to sign you in. Privacy

darning

Repairing a hole or thin spot by weaving new thread across it, so the gap fills with a small piece of new cloth.

It was once an everyday household skill for socks and sweaters. Today it is part of visible mending, where the repair is shown off in a contrasting color.

warp

The set of parallel threads you lay first, running in one direction across the hole.

The word comes from weaving on a loom, where the warp threads are stretched first and everything else is woven through them.

weft

The threads you weave across the warp at right angles, going over one and under the next.

darning egg

A smooth, egg-shaped tool slid inside a sock to hold it in shape while you darn.

A darning mushroom does the same job with a handle. A mug, ladle, orange or tennis ball works just as well for a first try.

running stitch

The simplest hand stitch: the needle goes down and up along a line, leaving a dashed line of thread on top.

Swiss darning

A different repair that follows the sock's own V-shaped knit stitches with new yarn, used to strengthen thin spots before they become holes.

It is also called duplicate stitch. It blends in better than a woven darn but does not bridge an open hole.

Get new hobbies by email

A short email when new hobbies and new levels land. No spam, unsubscribe anytime.

We only use your email to send these. Privacy

Tell us what you think

We only use your email to reply. Privacy