Skip to content
AtomicHobbies

Small hobbies for the gaps in your day.

All hobbies
Craftsbeginner30 minutes

Wire-Wrapped Stone Pendant

Wire wrapping holds a stone in a small cage of bent wire, so a pebble with no hole can hang on a cord. It is how many people turn a beach stone, a garden find or a tumbled crystal into a necklace, and the first one needs no soldering and no special tools. A smooth pebble, a short length of craft wire and a piece of string are enough for a pendant you can wear the same day.

What you'll do

Pick a smooth pebble, twist 75 cm of wire into a hanging loop, wrap it around the stone's edge, cross the front and back to lock it in a cage, tuck the ends and hang it on a cord you can wear.

A smooth oval pebble held in a simple copper wire cage, with a twisted loop at the top threaded on a cord.

At a glance

Time
30 minutes for your first session
Cost
One thing to get, under $15: Soft craft or jewelry wire, 20 or 22 gauge (0.8 or 0.6 mm)
You need
A smooth pebble or tumbled stone, 2.5 to 4 cm (1 to 1 1/2 inches) long, Soft craft or jewelry wire, 20 or 22 gauge (0.8 or 0.6 mm), A cord to hang it on, Something to cut wire, A pen or marker, and a ruler or tape measure

What you need

Required

  • A smooth pebble or tumbled stone, 2.5 to 4 cm (1 to 1 1/2 inches) long × 1, plus a spare in case the first is the wrong shape · $0 · household

    Flat ovals and egg shapes about 1 to 2 cm thick wrap most easily; a stone a little narrower at one end, or with a slight waist, holds the wire best. Avoid perfectly round balls, which slip out, and very thin slices. A garden, driveway or beach pebble works, or a tumbled stone you already own. Only collect where it is allowed: many parks, including US national parks, forbid taking rocks.

    Alternatives: A tumbled stone or crystal you already have, A piece of sea glass with smooth edges

  • Soft craft or jewelry wire, 20 or 22 gauge (0.8 or 0.6 mm) × 75 cm (30 inches) per pendant · $4-15 for a 6-yard (5.5 m) spool · purchased

    Copper or coated copper craft wire, sold in craft stores and online, bends with your fingers and holds its shape. A 6-yard spool makes about 7 pendants. 20 gauge holds a firmer cage; 22 gauge is easier on the fingers. Skip 18 gauge and thicker, which is too stiff to shape by hand. Paper clips do not work: each is only about 10 cm of springy 1 mm steel. Bread-bag twist ties are too short and too weak. If you already have a reel of floral wire or thin, soft garden wire, try that first.

    Alternatives: Floral wire you already have, used doubled if it is thinner than 22 gauge, Thin, soft garden or plant-tie wire that bends easily by hand, Two solid copper strands from a scrap network (Ethernet) cable, twisted together, with the plastic coating left on or stripped off

  • A cord to hang it on × 75 cm (30 inches) · $0 · household

    Cotton string, yarn, thin ribbon, a leather lace or a chain you already have. It must fit through a loop about 1 cm (3/8 inch) across.

    Alternatives: A necklace chain you already own, Embroidery floss braided into a cord

  • Something to cut wire × 1 · $0 · household

    Wire cutters, the cutting part of ordinary pliers, or an old pair of nail clippers all cut 20 and 22 gauge wire. Do not use good scissors: wire nicks the blades. Use ordinary scissors for the cord.

    Alternatives: Old nail clippers, Combination pliers with a cutting edge

  • A pen or marker, and a ruler or tape measure × 1 each · $0 · household

    The pen barrel, about 8 to 10 mm (3/8 inch) across, shapes the hanging loop. The ruler measures the wire and cord.

Nice to have

  • Small pliers, flat-nose or needle-nose × 1 · $0 · household

    Handy for gripping, tightening and pressing the cut ends flat, but fingers and a thumbnail do the job on soft wire. A jewelry pliers set costs about $10-20 if you keep going.

How to do it

  1. Pick a stone 2.5 to 4 cm (1 to 1 1/2 inches) long and 1 to 2 cm thick, smooth all over, with no sharp chips. Wash it with soap and water and dry it completely with a towel, since a damp stone lets the wire slide. Decide which end is the top (the narrower end if there is one) and which face is the front (the nicer side). It worked if the stone sits steady between your thumb and finger and you know which way up it goes. Common mistake: choosing a big or round stone. Anything over 5 cm needs more wire than you will cut, and a ball shape has no edge to hold the wire, so it slips out.

    Show help

    tumbled stone: A small stone, often a crystal or semi-precious stone, polished smooth by a few weeks of turning in a drum with grit.

    Tip: Common mistake: overworking the wire. Every bend and rebend makes copper harder and more brittle, so plan where a wire goes before you bend it, and if a section gets stiff and kinked, cut it off rather than straightening it again and again.

  2. Measure and cut 75 cm (30 inches) of wire. Run it between your thumb and finger 2 or 3 times to take out the curl from the spool. Fold it in half so the two ends meet. Hook the fold over your pen so the pen sits inside the bend and the two halves hang down evenly. Bring both halves together just under the pen, pinch them there, and turn the pen 3 full turns while holding the two wires still, so they twist together into a short neck about 1 cm (3/8 inch) long right under the pen. Slide the pen out. You now have a round loop at the top, the , a twisted neck, and two tails about 33 cm (13 inches) long. It worked if the loop keeps its shape when you let go and the tip of your cord pushes through it. Common mistake: twisting more than 4 or 5 turns, which hardens the wire until it snaps at the neck. Three turns is plenty.

    Show help

    bail: The loop at the top of a pendant that the cord or chain goes through.

    work hardening: The way soft wire gets stiffer and more brittle each time it is bent, until it can snap.

    Tip: Common mistake: overworking the wire. Every bend and rebend makes copper harder and more brittle, so plan where a wire goes before you bend it, and if a section gets stiff and kinked, cut it off rather than straightening it again and again.

  3. Hold the stone top up, with the twisted neck sitting right on the top edge, centered, and the loop sticking up above it. Take one tail down the left edge of the stone and the other down the right edge, pressing each wire onto the rim (the narrow side of the stone, not the flat face) with your thumb as you go. Where they meet at the bottom center, cross them and twist them together 2 full turns, pulling snug against the bottom of the stone. Now the wire runs all the way round the stone's edge like a belt. It worked if the wire touches the rim all round with no gap wider than 2 to 3 mm (1/8 inch), and the neck still sits on top. The stone may still slide out of the front or back; the next step fixes that. Common mistake: letting the wire wander onto the front face. Keep it on the edge, or the cage will be lopsided.

    Show help

    Tip: Common mistake: overworking the wire. Every bend and rebend makes copper harder and more brittle, so plan where a wire goes before you bend it, and if a section gets stiff and kinked, cut it off rather than straightening it again and again.

  4. Pick either tail at the bottom twist and lay it diagonally up across the front face to the right edge, about halfway up the stone. Wrap it once around the edge band there: pass it behind the band and back over it to the front, then pull snug. Carry it on, diagonally up across the front face, to the neck at the top, and wrap it 2 times around the neck just under the loop. Do the same with the other tail across the back: up to the left edge halfway, once around the band, then across the back to the neck and 2 wraps around it. The front now shows a zigzag line of wire, and the back a mirror of it. It worked if you press the stone with your thumb from the front and then from the back and it does not pop out, and the wire lines sit flat on both faces. Common mistake: pulling so hard that the edge band slides off the rim onto a face. Pull until the wire touches the stone, then stop.

    Show help

    cage wrap: A way of holding a stone that has no drilled hole by surrounding it with lines of wire, like a small net.

    Tip: Common mistake: overworking the wire. Every bend and rebend makes copper harder and more brittle, so plan where a wire goes before you bend it, and if a section gets stiff and kinked, cut it off rather than straightening it again and again.

  5. Shake the pendant gently. If the stone rattles, tighten the loosest stretch of wire on a face: pinch it in the middle between your fingertips (or pliers) and twist a half turn, which puts a small zigzag in it and pulls it tight. One kink per loose line is enough. Then wrap any leftover tail 1 or 2 more times around the neck, cut it so 5 mm (1/4 inch) is left, and press that end flat against the neck with your thumbnail, the back of a spoon or pliers. Do the same with the other tail. It worked if the stone does not move when you shake it, and a tissue dragged over the whole pendant does not catch anywhere. Common mistake: leaving a cut end sticking out. It scratches skin and snags sweaters, so press both ends down until the tissue slides past.

    Show help

    kink: A small zigzag twisted into a stretch of wire to take up slack and pull the cage tight against the stone.

    Tip: Common mistake: overworking the wire. Every bend and rebend makes copper harder and more brittle, so plan where a wire goes before you bend it, and if a section gets stiff and kinked, cut it off rather than straightening it again and again.

  6. Cut 75 cm (30 inches) of cord. Push one end through the loop, bring both ends together and tie them in an overhand knot (make a loop with both ends held as one, pass them through it, and pull tight), leaving 1 to 2 cm tails. That makes a necklace about 70 cm round that slips over your head and hangs at mid-chest. Turn the pendant so the front faces out. It worked if it goes over your head without catching and hangs face forward. You did it: a stone you picked is now a pendant you can wear. Some people choose a stone for its color, for where they found it or for what it means to them, and a stone from a walk or a trip makes a good small gift. Next session, wrap a stone of a different shape, or add a second pass of wire across each face for a fuller cage.

    Show help

    Tip: Common mistake: overworking the wire. Every bend and rebend makes copper harder and more brittle, so plan where a wire goes before you bend it, and if a section gets stiff and kinked, cut it off rather than straightening it again and again.

Wire-Wrapped Stone Pendant · Step 1 of 6

Tips

  • Common mistake: overworking the wire. Every bend and rebend makes copper harder and more brittle, so plan where a wire goes before you bend it, and if a section gets stiff and kinked, cut it off rather than straightening it again and again.

  • Practice on an ordinary pebble before wrapping a stone you care about. Your second and third pendants will be much neater, and a spool has wire for about 7.

  • Keep the stone pressed against the twisted neck with one thumb the whole time you wrap. Most loose cages start because the stone slid down while the band was going on.

  • Bare copper darkens over weeks and can leave a faint green mark on skin, which washes off. Coated craft wire keeps its color longer, and a thin coat of clear nail polish on bare copper slows the darkening.

  • Cut ends are sharp. Point the wire away from your face when you cut it, and keep small offcuts in a jar lid so they do not end up in feet or pets.

Glossary

bail
The loop at the top of a pendant that the cord or chain goes through.
gauge
The number that gives a wire's thickness. The higher the number, the thinner the wire.
cage wrap
A way of holding a stone that has no drilled hole by surrounding it with lines of wire, like a small net.
tumbled stone
A small stone, often a crystal or semi-precious stone, polished smooth by a few weeks of turning in a drum with grit.
kink
A small zigzag twisted into a stretch of wire to take up slack and pull the cage tight against the stone.
work hardening
The way soft wire gets stiffer and more brittle each time it is bent, until it can snap.

Communities

Resources

Frequently asked questions

How long does it take to learn wire wrapping?

A first simple cage takes about 30 minutes. After 3 or 4 pendants you can wrap one in 15 minutes, and the cuts and tucked ends look much neater. Woven and spiral designs take a few weeks of practice.

Can I use paper clips or other wire from around the house?

Paper clips are only about 10 cm of stiff steel each, too short and springy for a cage, and bread-bag twist ties are too short and weak. Floral wire, thin soft garden wire, or two copper strands from a scrap network cable twisted together can work. If you have none, a small spool of craft wire is the one thing to buy.

Do I need jewelry pliers?

Not for this pendant. Fingers, a pen and something to cut wire are enough with 20 or 22 gauge soft wire. Flat-nose and round-nose pliers make neater loops and ends, so they are worth getting if you keep going.

My stone keeps slipping out of the wire. What went wrong?

Usually the stone is too round, or the edge band slid onto a face. Choose a flatter stone or one with a narrow end, keep the band on the rim, and put a small kink in the loosest wire to pull it tight. If it still slips, add one more line of wire across each face.

Will copper wire turn my skin green?

Bare copper can leave a faint green mark on skin, especially when it is warm or damp. It is harmless and washes off. Coated craft wire or a coat of clear nail polish over the wire prevents most of it.

Does it matter which stone I use?

For wrapping, only the shape matters: smooth, flattish and 2.5 to 4 cm long is easiest. Beyond that, pick anything you like. Many people choose a stone for its color, for the place they found it, or for a meaning it holds for them.

Something off in this guide?

Tried it? Earn the badge

Rate it below and the Wire-Wrapped Stone Pendant badge goes in your account.

How was it?

How much of a challenge was it?

Pass it on

Did you enjoy wire-wrapped stone pendant? Share it with your friends!

Someone you know has 30 spare minutes too.

Sign in

A free account: just your email, no password. We'll email you a link that brings you back here.

No password. We only use your email to sign you in. Privacy

bail

The loop at the top of a pendant that the cord or chain goes through.

In this pendant the bail is the round loop you twist around the pen in step 2. Jewelers also make bails as separate metal parts, but a wire loop is the simplest kind.

gauge

The number that gives a wire's thickness. The higher the number, the thinner the wire.

20 gauge is about 0.8 mm and 22 gauge about 0.6 mm. Thicker wire such as 18 gauge holds shape well but is hard to bend by hand; thinner wire such as 26 gauge is used for weaving and fine details.

cage wrap

A way of holding a stone that has no drilled hole by surrounding it with lines of wire, like a small net.

The simplest cage, used here, is one band around the edge plus a line across each face. Fuller cages add more crossing lines or a spiral on the front.

tumbled stone

A small stone, often a crystal or semi-precious stone, polished smooth by a few weeks of turning in a drum with grit.

Tumbled stones are smooth and rounded like a beach pebble, which makes them easy to wrap. They are sold cheaply in rock shops and gift shops.

kink

A small zigzag twisted into a stretch of wire to take up slack and pull the cage tight against the stone.

Wire wrappers often use a few kinks on purpose as decoration. One per loose line is enough; too many make the wire brittle.

work hardening

The way soft wire gets stiffer and more brittle each time it is bent, until it can snap.

It is why you should bend each part of the wire as few times as possible and stop twisting the neck after 3 turns.

Get new hobbies by email

A short email when new hobbies and new levels land. No spam, unsubscribe anytime.

We only use your email to send these. Privacy

Tell us what you think

We only use your email to reply. Privacy